 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| CALIFORNIA MICRO DEVICES WLP200 Wafer Level Package Evaluation RC Filter Network Features * 6 Filters per device * Ultra small footprint, 0.5mm pitch * Silicon substrate * 0.30mm Eutectic Solder Bumps Applications * EMI filter for Mobile Equipment (e.g. Cellular Phones) * Evaluation Device Product Description The WLP200 consists of 6 RC filters with different filter characteristics in a wafer level package (WLP). All I/O pins are ESD protected for contact discharges up to 8KV per the IEC1000-4-2 level 4 specification. Two versions with different capacitor values are available. Cellular phone application frequently demands filtering of signals in the 800 to 2,700 MHz band. California Micro Devices' unique thin film Flip Chip filters provide a minimum of -30 dB of attenuation over this frequency band. The bump size and pitch of these filters are selected such that the device can be placed directly on a FR4 printed circuit board using conventional assembly techniques. Ground-bounce and cross-talk are minimized by a die design that provides eight solder bump contacts to the common supply connection. The solder bump contacts are a 63/37 Sn/Pb alloy and are nominally 0.30 mm in diameter. SCHEMATIC DIAGRAM C1 R 50 C GND D1 R 50 C GND D2 R 90 C GND GND A3 GND A2 R 50 GND A1 B1 D3 R 90 C R 90 GND GND A4 D4 R 70 C R 70 GND D5 R 70 C GND GND A5 GND C3 B3 C2 B2 GND C5 B5 C4 B4 (c) 2000 California Micro Devices Corp. All rights reserved. 11/10/2000 C1460800 215 Topaz Street, Milpitas, California 95035 Tel: (408) 263-3214 Fax: (408) 263-7846 www.calmicro.com 1 CALIFORNIA MICRO DEVICES WLP200 S TA N D A R D VA L U E S Ab s o l u t e To l e r a n c e R Ab s o l u t e To l e r a n c e C TCR of Resi st or s Op e r a t i n g Te mp e r a t u r e Ra n g e Leakage Cur r ent @ 6V Powe r Ra t i n g / Re s i s t o r 10% 20% 100ppm -40C to 85C <1A 100mW ELECTRICAL CHARACTERISTICS OF WLP200-01 Filter #1 #2 #3 #4 #5 #6 Filter Type TF T TF T T TF Input Pin C1 D1 D2 D3 D4 D5 Output Pin B1 A1 A2 A3 A4 A5 R() 50 50 90 90 70 70 C(pF) 135 135 135 135 135 135 Fc (Note 1) 23.6MHz 23.6MHz 13.1MHz 13.1MHz 16.8MHz 16.8MHz Fc (Note 2) 36.0MHz 23.6MHz 32.8MHz 18.5MHz 21.6MHz 34.1MHz ELECTRICAL CHARACTERISTICS OF WLP200-02 Filter #1 #2 #3 #4 #5 #6 Filter Type TF T TF T T TF Input Pin C1 D1 D2 D3 D4 D5 Output Pin B1 A1 A2 A3 A4 A5 R() 50 50 90 90 70 70 C(pF) 190 190 190 190 190 190 Fc (Note 1) 16.7MHz 16.7MHz 9.30MHz 9.30MHz 12.0MHz 12.0MHz Fc (Note 2) 25.7MHz 18.0MHz 23.2MHz 13.2MHz 15.3MHz 24.4MHz * Note 1: Calculated with zero Source impedance and infinite Load impedance. * Note 2: Calculated with 50 Source impedance and 50 Load impedance. 2.538mm 0.5mm 0.269 mm D C B A 0.3mm Dia. Bumps 1 2 3 4 5 0.218 mm 0.635mm 0.860mm 0.5 mm 1.936mm Figure 2. WLP200 Package Diagram (View of the Bump side) (c)2000 California Micro Devices Corp. All rights reserved. 2 215 Topaz Street, Milpitas, California 95035 Tel: (408) 263-3214 Fax: (408) 263-7846 www.calmicro.com 11/10/2000 CALIFORNIA MICRO DEVICES WLP200 P R I N T E D C I R C U I T B OA R D R E C O M M E N D AT I O N S Pa d Si ze o n PCB Pa d Sh a p e Pa d De f i n i t i o n So l d e r Ma s k Op e n i n g S o l d e r S t e n c i l T h i ck n e s s Sol der St enc i l Aper t ur e Openi ng Sol der Fl ux Rat i o No Cl e a n So l d e r Pa s t e Bo n d Tr a c e F i n i s h OSP (Entek Cu Plus 106A) 0 . 2 7 5 mm Round No n So l d e r Ma s k De f i n e d Pa d s ( NSMD) 0 . 3 2 5 mm 0 . 1 5 2 mm 0 . 3 3 mm ( s q . ) 50/50 ESD SPECIFICATIONS ESD Protection (Guaranteed by Design) Peak Discharge Voltage at any I/O, Human Body Model, Method 3015 (Note 1) In System Protection, IEC 1000-4-2, Level 4 (Note 2 & 3) Channel Clamp Voltage @ 8KV ESD Pulses, Human Body Model (Notes 1 & 2) Note 1: Human Body Model per MIL-STD-883, Method 3015 CDischarge = 100pF, RDischarge = 1.5K, pins B2, C2, B3, C3, B4, C4, B5, C5 are at ground. ESD Contact Discharge from pins B1, A1, A2, A3, A4 and A5 one at a time. Note 2: Pins B2, C2, B3, C3, B4, C4, B5, C5 are grounded. ESD Contact Discharge between pins B1, A1, A2, A3, A4 and A5 and ground one at a time. Note 3: Standard IEC 1000-4-2 with CDischarge = 150pF, RDischarge = 330, pins B2, C2, B3, C3, B4, C4, B5, C5 are at ground. MIN -15KV -8KV -30V MAX 15KV 8KV 30V Typical Solder Reflow Thermal Profile (No Clean Flux) 250 EXH 225 200 PH Z2 Z3 Z4 Z5 RF CD EXH Temperature (oC) 175 150 125 100 75 50 25 0 48 97 145 194 Time (s) 242 290 339 387 435 (c) 2000 California Micro Devices Corp. All rights reserved. 11/10/2000 215 Topaz Street, Milpitas, California 95035 Tel: (408) 263-3214 Fax: (408) 263-7846 www.calmicro.com 3 CALIFORNIA MICRO DEVICES WLP200-01 FILTER CHARACTERISTICS (S21) MEASUREMENT WLP200 NOTE: All the measurements are done with 50-source & 50-load impedance using a HP8753C Network Analyzer with a HP85047A S-parameter Test Set. S21 log MAG 1 5 dB/ REF 0 dB S21 log MAG 1 5 dB/ REF 0 dB 2 3 1: -3.5204 dB 1.000 000 MHz 2: -6.5215 dB 36.03 MHz 3: -11.188 dB 80 MHz 4: -29.436 dB 800 MHz 1: -5.9489 dB 1.000 000 MHz 2: -8.9432 dB 25.461 MHz 3: -16.269 dB 80 MHz 4: -38.011 dB 800 MHz 2 3 4 4 START .300 000 MHz STOP 3 000.000 000 MHz START .300 000 MHz STOP 3 000.000 000 MHz WLP200-01 Filter #1 C1-B1 WLP200-01 Filter #2 D1-A1 S21 log MAG 1 5 dB/ REF 0 dB S21 log MAG 5 dB/ REF 0 dB 1 2 3 1: -5.5407 dB 1.000 000 MHz 2: -8.542 dB 32.75 MHz 3: -13.941 dB 80 MHz 4: -32.441 dB 800 MHz 1: -8.8303 dB 1.000 000 MHz 2: -11.831 dB 18.5 MHz 3: -21.81 dB 80 MHz 4: -45.253 dB 800 MHz 2 3 4 4 START .300 000 MHz STOP 3 000.000 000 MHz START .300 000 MHz STOP 3 000.000 000 MHz WLP200-01 Filter #3 D2-A2 WLP200-01 Filter #4 D3-A3 (c)2000 California Micro Devices Corp. All rights reserved. 4 215 Topaz Street, Milpitas, California 95035 Tel: (408) 263-3214 Fax: (408) 263-7846 www.calmicro.com 11/10/2000 CALIFORNIA MICRO DEVICES WLP200-01 FILTER CHARACTERISTICS (S21) MEASUREMENT (Continued) WLP200 NOTE: All the measurements are done with 50-source & 50-load impedance using a HP8753C Network Analyzer with a HP85047A S-parameter Test Set. S21 log MAG 1 5 dB/ REF 0 dB S21 log MAG 1 5 dB/ REF 0 dB 2 2 3 1: -7.5079 dB 1.000 000 MHz 2: -10.504 dB 21.55 MHz 3: -19.2 dB 80 MHz 4: -41.775 dB 800 MHz 3 1: -4.6323 dB 1.000 000 MHz 2: -7.625 dB 34.1 MHz 3: -12.677 dB 80 MHz 4: -29.358 dB 800 MHz 4 4 START .300 000 MHz STOP 3 000.000 000 MHz START .300 000 MHz STOP 3 000.000 000 MHz WLP200-01 Filter #5 D4-A4 WLP200-01 Filter #6 D5-A5 WLP200-02 FILTER CHARACTERISTICS (S21) MEASUREMENT NOTE: All the measurements are done with 50-source & 50-load impedance using a HP8753C Network Analyzer with a HP85047A S-parameter Test Set. S21 log MAG 1 5 dB/ REF 0 dB S21 log MAG 1 5 dB/ REF 0 dB 2 2 3 1: -3.4364 dB 1.000 000 MHz 2: -6.44 dB 25.7 MHz 3: -13.557 dB 80 MHz 4: -31.79 dB 800 MHz 1: -5.8804 dB 1.000 000 MHz 2: -8.8746 dB 18 MHz 3: -18.985 dB 80 MHz 4: -40.299 dB 800 MHz 3 4 4 START .300 000 MHz STOP 3 000.000 000 MHz START .300 000 MHz STOP 3 000.000 000 MHz WLP200-02 Filter #1 C1-B1 (c) 2000 California Micro Devices Corp. All rights reserved. 11/10/2000 WLP200-02 Filter #2 D1-A1 Tel: (408) 263-3214 Fax: (408) 263-7846 www.calmicro.com 215 Topaz Street, Milpitas, California 95035 5 CALIFORNIA MICRO DEVICES WLP200 WLP200-02 FILTER CHARACTERISTICS (S21) MEASUREMENT (Continued) NOTE: All the measurements are done with 50-source & 50-load impedance using a HP8753C Network Analyzer with a HP85047A S-parameter Test Set. S21 log MAG 1 1 2 3 1: -5.4737 dB 1.000 000 MHz 2: -8.478 dB 23.23 MHz 3: -11.423 dB 40 MHz 4: -29.674 dB 400 MHz 2 1: -8.7223 dB 1.000 000 MHz 2: -11.74 dB 13.2 MHz 3: -16.641 dB 30 MHz 4: -36.565 dB 300 MHz 3 5 dB/ REF 0 dB S21 log MAG 5 dB/ REF 0 dB 4 4 START .300 000 MHz STOP 3 000.000 000 MHz START .300 000 MHz STOP 3 000.000 000 MHz WLP200-02 Filter #3 D2-A2 WLP200-02 Filter #4 D3-A3 S21 log MAG 1 5 dB/ REF 0 dB S21 log MAG 1 5 dB/ REF 0 dB 2 2 1: -7.3998 dB 1.000 000 MHz 2: -10.4 dB 15.28 MHz 3: -16.318 dB 40 MHz 4: -36.504 dB 400 MHz 3 3 1: -4.5251 dB 1.000 000 MHz 2: -7.522 dB 24.351 MHz 3: -10.163 dB 40 MHz 4: -27.65 dB 400 MHz 4 4 START .300 000 MHz STOP 3 000.000 000 MHz START .300 000 MHz STOP 3 000.000 000 MHz WLP200-02 Filter #5 D4-A4 WLP200-02 Filter #6 D5-A5 (c)2000 California Micro Devices Corp. All rights reserved. 6 215 Topaz Street, Milpitas, California 95035 Tel: (408) 263-3214 Fax: (408) 263-7846 www.calmicro.com 11/10/2000 |
Price & Availability of WLP200
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |